Toyota Tundra Key Fob Battery Replacement

2020-2021 Models

This vehicle has multiple key fob types. Select your key below.

Most Common

Smart Key Fob

Battery Type

CR2032

Buy CR2032 on Amazon

✓ OEM Compatible

✓ Free Prime Shipping

Toyota Tundra Smart Key Fob Battery Replacement Video

FCC ID: HYQ14FBA, HYQ14FBB

Replacement Steps for Smart Key Fob

Take out the emergency key Press or slide the release on the Toyota Tundra smart key fob and pull the metal key blade out. The slot it leaves is your way into the case.

Open the case Separate the two halves at the seam, working slowly around the edge.

Mind the circuit board The circuit board can come loose once the case is open. Hold it by its edges and keep fingers off the contacts.

Take out the old battery Note which way the CR2032 faces, then lift it out with a fingernail or a small screwdriver tip.

Fit the new battery Put the new CR2032 in with the positive (+) side facing up, and press it flat into its holder.

Check the rubber pad Make sure the rubber button pad or seal sits flat before closing, or the buttons may stick.

Close it up and test Line up the halves and press until they click, slide the emergency key back in, then try lock and unlock from a few feet away.

Alternative

Remote Head Key

Battery Type

CR2016

Buy CR2016 on Amazon

✓ OEM Compatible

✓ Free Prime Shipping

Toyota Tundra Remote Head Key Battery Replacement Video

FCC ID: GQ4-52T

Replacement Steps for Remote Head Key

Locate the release button on the back of your key fob. Press it to slide out the emergency metal key blade.

Use the key blade as a pry tool. Insert it into the seam along the edge of the fob and gently twist to separate the two halves of the case.

Remove the old battery. Note the orientation — the positive (+) side typically faces up. A small flathead screwdriver can help pop it out.

Insert the new battery with the positive (+) side facing the same direction as the old one. Press firmly until it clicks into place.

Snap the case back together. Align both halves and press around the edges until you hear it click shut. Slide the emergency key back in.

Test all buttons — lock, unlock, trunk, and panic — to confirm the new battery is working properly.

Alternative

Remote Key Fob

Battery Type

CR2016

Buy CR2016 on Amazon

✓ OEM Compatible

✓ Free Prime Shipping

Toyota Tundra Remote Key Fob Battery Replacement Video

FCC ID: GQ4-52T

Replacement Steps for Remote Key Fob

Locate the release button on the back of your key fob. Press it to slide out the emergency metal key blade.

Use the key blade as a pry tool. Insert it into the seam along the edge of the fob and gently twist to separate the two halves of the case.

Remove the old battery. Note the orientation — the positive (+) side typically faces up. A small flathead screwdriver can help pop it out.

Insert the new battery with the positive (+) side facing the same direction as the old one. Press firmly until it clicks into place.

Snap the case back together. Align both halves and press around the edges until you hear it click shut. Slide the emergency key back in.

Test all buttons — lock, unlock, trunk, and panic — to confirm the new battery is working properly.

Frequently Asked Questions

What battery does a Toyota Tundra key fob use?

It depends on the key: the Smart Key Fob uses a CR2032; the Remote Head Key uses a CR2016; the Remote Key Fob uses a CR2016. All are 3-volt lithium coin batteries, available at most grocery stores, pharmacies, and online retailers.

How do I know if my Toyota Tundra key fob battery is dying?

Signs your Toyota Tundra key fob battery is dying include: reduced range (having to get closer to unlock), intermittent button response, delayed unlocking, the low battery warning on your dashboard, or buttons requiring multiple presses to work.

How long does a Toyota Tundra key fob battery last?

A Toyota Tundra key fob battery typically lasts 2-4 years depending on usage. Frequent use, extreme temperatures, and proximity to electronic devices can shorten battery life.

Can I replace my Toyota Tundra key fob battery myself?

Yes, replacing a Toyota Tundra key fob battery is a simple DIY task that takes under 5 minutes. You only need a new CR2032 or CR2016 battery and optionally a small flathead screwdriver. No dealer visit or programming is required.

Do I need to reprogram my key fob after replacing the battery?

No, you do not need to reprogram your Toyota Tundra key fob after replacing the battery. The fob retains its programming during battery changes. Simply insert the new battery and test the buttons.

Where can I buy a CR2032 or CR2016 battery?

CR2032 or CR2016 batteries are available at Walmart, Target, CVS, Walgreens, Amazon, auto parts stores like AutoZone and O'Reilly, and most grocery stores. They typically cost $6-12 for a 2-pack.

Toyota Tundra Key Fob Battery Replacement

Smart Key Fob

Remote Head Key

Remote Key Fob

Frequently Asked Questions

Related Searches